Free Express Courier Freight across Victoria & Metro Australia on orders over $1,500 AUD
Motor Systems•2026-06-18•8 min read

Mid-Drive Motors vs Hub Motors: Hill Climbing Torque & Efficiency Compared

Mid-Drive Motors vs Hub Motors: Hill Climbing Torque & Efficiency Compared
Photo: nottheviewsofmyemployer, CC BY 2.0

How Bosch, Shimano STEPS, and Bafang mid-drive systems perform compared to high-torque rear hub motors on steep city hills.

The motor is the heart of any e-bike, and the two dominant architectures — mid-drive and hub motor — suit fundamentally different riding styles. If your commute involves hills, this comparison matters more than almost any other spec on the page.

Mid-Drive Motors: How They Work

A mid-drive motor sits at the bottom bracket, between the pedals. It drives the chain (or belt), which means it works through the bike's gears. When you shift to a lower gear on a steep climb, the motor's torque is multiplied by the mechanical advantage of the drivetrain — the same principle that makes a low-gear pedal stroke easier for your legs.

Popular mid-drive systems in Australia include:

  • Bosch Performance Line CX: 85 Nm torque, widely regarded as the benchmark for eMTB
  • Shimano STEPS EP8: 85 Nm, lighter and quieter than Bosch, strong in trail riding
  • Bafang M400/M500: 80–95 Nm, common on value-oriented commuter bikes
  • Bafang BBS02B/BBSHD: aftermarket mid-drive kits for converting existing bikes (750 W–1000 W)

Hub Motors: How They Work

A hub motor is built into the centre of the front or rear wheel. It drives the wheel directly, bypassing the gears entirely. This makes hub motors mechanically simpler but less efficient at low speeds and high loads (exactly the conditions you face on a steep hill).

Hub motors come in two types:

  • Geared hub motors: smaller, lighter, with internal planetary gears. Good torque at low speed, freewheel when the motor is off. Typically 40–60 Nm.
  • Direct-drive hub motors: larger, heavier, no internal gears. Higher top speed, regenerative braking possible, but heavier drag when unpowered. Typically 30–50 Nm.

Hill Climbing: The Critical Difference

On a 10 % gradient (common in hilly suburbs like Melbourne's Kew, Sydney's Mosman, or Brisbane's Paddington), the difference is stark:

Factor Mid-drive (85 Nm) Hub motor (45 Nm)
Sustained climbing speed 18–22 km/h 10–15 km/h
Motor temperature after 2 km climb Warm Hot (may throttle)
Rider effort required Low–moderate Moderate–high
Chain/drivetrain wear on hills Higher (motor drives through chain) None (motor drives wheel directly)
Noise on steep climbs Moderate whine Quiet

Mid-drives multiply torque through the gears. In the lowest gear on a Shimano 11-speed, an 85 Nm mid-drive motor effectively delivers over 200 Nm at the rear wheel. A 45 Nm hub motor delivers 45 Nm regardless of gear selection.

Flat-Ground Commuting: Hub Motors Shine

On flat terrain, hub motors have advantages:

  • Simpler mechanics: no chain wear from motor torque, no mid-drive servicing
  • Lower noise: direct-drive hubs are nearly silent
  • Regenerative braking (direct-drive only): recovers 5–10 % of energy on descents
  • Lower cost: hub motor e-bikes are typically $500–$1,500 cheaper than mid-drive equivalents

If your commute is mostly flat — think Melbourne's inner north, Adelaide's CBD, or Perth's coastal suburbs — a rear hub motor delivers smooth, quiet, reliable assistance with minimal maintenance.

Efficiency and Range

Mid-drive motors are 10–15 % more efficient than hub motors because they leverage the bike's gearing. In practice, this means:

  • A 500 Wh battery on a mid-drive bike gives roughly 60–80 km range
  • The same 500 Wh battery on a hub motor bike gives roughly 50–70 km range

The gap widens in hilly terrain and narrows on flat ground.

Reliability and Maintenance

Hub motors have fewer service requirements. The motor is sealed in the wheel, and the bike's chain and gears only carry pedal force (not motor force). A hub motor can last the life of the bike with zero motor-specific maintenance.

Mid-drive motors put all their torque through the chain and sprockets. This accelerates chain stretch and cassette wear — expect to replace chains 30–50 % more often than on a non-assisted bike. The motor itself is reliable, but the drivetrain around it needs attention.

Which Is Right for You?

Choose a mid-drive if:

  • Your route includes sustained climbs above 8 % gradient
  • You ride off-road or on mixed terrain
  • You want maximum efficiency per watt-hour
  • You are comfortable with regular drivetrain maintenance

Choose a hub motor if:

  • Your route is mostly flat or gently rolling
  • You value simplicity and low maintenance
  • You want a quieter ride
  • Budget is a primary concern

Conversion Kits: A Third Option

If you already own a bike you love, aftermarket conversion kits let you add electric assist:

  • Bafang BBS02B (750 W mid-drive): the most popular mid-drive kit. Fits most standard bottom brackets. Strong hill performance.
  • Bafang BBSHD (1000 W mid-drive): for riders who need serious torque. Suited to cargo bikes and steep terrain.
  • Voilamart / EBIKELING hub motor kits: 500 W–1500 W rear hub motors. Simpler installation, better for flat routes.

Conversion kits let you match the motor type to your terrain without buying a whole new bike.

Ready to Find Your E-Bike?

Browse commuter, cargo, folding and mountain e-bikes from Brunswick, Victoria, with express freight across Australia.

Shop E-Bikes →

Shop related to this guide

More guides